cusma.4B.730810.c1844

{
  "source": {
    "url": "https://www.international.gc.ca/trade-commerce/trade-agreements-accords-commerciaux/agr-acc/cusma-aceum/text-texte/04.aspx?lang=eng",
    "sha256": "7e30ee34f87778849e969da6f7c05f8861e45bc0ae454d04ddde39fcd539e1b5",
    "text_en": "Note: Beginning on January 1 2020 or the date of entry into force of the Agreement, whichever is later, until December 31, 2021 or two years after entry into force of this Agreement, whichever is later, the following rules of origin shall apply to subheading 7308.10: A change to subheading 7308.10 from any other heading, except for changes resulting from the following processes performed on angles, shapes, or sections of heading 72.16: (a) drilling, punching, notching, cutting, cambering, or sweeping, whether performed individually or in combination; (b) adding attachments or weldments for composite construction; (c) adding attachments for handling purposes; (d) adding weldments, connectors or attachments to H-sections or I-sections, provided that the maximum dimension of the weldments, connectors, or attachments is not greater than the dimension between the inner surfaces of the flanges of the H-sections or I-sections; (e) painting, galvanizing, or otherwise coating; or (f) adding a simple base plate without stiffening elements, individually or in combination with drilling, punching, notching, or cutting, to create an article suitable as a column.",
    "text_fr": "Aucun changement nécessaire de la classification tarifaire à la sous-position 7308.10, à la condition que la teneur en valeur régionale ne soit pas inférieure à : a) 75 p. 100 lorsque la méthode de la valeur transactionnelle est utilisée, ou b) 65 p. 100 lorsque la méthode du coût net est utilisée.",
    "citation": "CUSMA Annex 4-B (Global Affairs Canada consolidated text), Annex 4-B, Section B, Chapter 73 Articles of Iron or Steel, 7308.10",
    "retrieved_at": "2026-11-02T04:21:43.558Z"
  },
  "rule_id": "cusma.4B.730810.c1844",
  "agreement": "CUSMA",
  "effective": {
    "to": "2022-07-01",
    "from": "2020-07-01"
  },
  "applies_to": {
    "code": "730810",
    "level": "subheading"
  },
  "hs_edition": "HS2022",
  "party_scope": "all",
  "alternatives": [
    {
      "all_of": [
        {
          "tariff_shift": {
            "from": "any_other_heading",
            "review_materials": [
              {
                "text": "changes resulting from the following processes performed on angles, shapes, or sections of heading 72.16: (a) drilling, punching, notching, cutting, cambering, or sweeping, whether performed individually or in combination; (b) adding attachments or weldments for composite construction; (c) adding attachments for handling purposes; (d) adding weldments, connectors or attachments to H-sections or I-sections, provided that the maximum dimension of the weldments, connectors, or attachments is not greater than the dimension between the inner surfaces of the flanges of the H-sections or I-sections; (e) painting, galvanizing, or otherwise coating; or (f) adding a simple base plate without stiffening elements, individually or in combination with drilling, punching, notching, or cutting, to create an article suitable as a column",
                "codes": [
                  "7216"
                ],
                "effect": "excepted"
              }
            ]
          }
        }
      ]
    }
  ]
}